It is easy to install this invisible non-mortise barrel hinge used for wood panels 3/4' thick. Just drill the proper size hole and tap the hinge in flush. Secure mounting in the wood door or panel is assured by tightening the tensioning screw to expand the body of the hinge tightly in the hole.

Cutting a door hinge mortise with a chisel. A hinge mortise is the shallow cut made in the edge of a door and the door jamb that mirrors the size and thickness of the door hinge. 2.0 box office. The hinge mortise allows the hinge to be mounted flush with the jamb and door so the door will close properly. Hinge mortises on a door are often cut by machine with a router and straight bit, but you can cut mortises by hand using a hammer and chisel as well.

To do a good job cutting mortises, the chisel needs to be razor sharp. To cut hinge mortises on a door: • Screw the hinge to the door or jamb. • Screw the hinge to the door and jamb, so the top of the hinge is flush with the door edge and door jamb. Watch this video to find out more. Further Information • (video) • (video) • (video) • (video) Danny Lipford: Now, installing a door at your house is fairly easy, but to recess hinges like this is a little more of a challenge. Joe Truini: That’s right, Danny.

Most mortises are routed out, but here’s an alternative method. Screw the hinge directly to the edge of the door, and then mark its outline with a utility knife.

Remove the hinge and use a chisel to chop out around the outline. Just remember to keep the bevel end of the chisel facing toward the waste area, so you wind up with a nice, crisp line. And then hold the chisel perfectly vertical, and make a series of cuts about an eighth-inch apart all the way across the waste area.

Then turn the chisel.. Hold the chisel flat, with the bevel facing up, and scrape out all the waste wood. To finish up, hold the chisel bevel down and smooth out the bottom of the mortise. Danny Lipford: Now, this is an exterior door, so we’ll be using three hinges on this installation.

But if you have an interior door you’re installing, two hinges is usually sufficient. Works great depending on the wood type and grain. I recently made a new shed door from treated deck boards and the chisel did not help. I scored the hinge area with a razor knife, scored cuts an eighth inch apart then of went the other way(crossed cuts like a tic tack toe grid). Used a regular pocket knife to “pop” out the little squares.

Worked great but wasn’t as pretty until I sanded We want to hear from you! In addition to posting comments on articles and videos, you can also send your comments and questions to us on our or at (800) 946-4420. While we can't answer them all, we may use your question on our Today's Homeowner radio or TV show, or online at todayshomeowner.com. Name (required) Email (will not be published) (required) characters available.

The hinges are exactly what I needed and worked well for my application. Buku armageddon peperangan akhir zaman pdf to word. When I reinstall the hinges after painting I'm going to need to replace all the screws since the heads on a large percentage of them stripped out on the initial installation. A note on the service I received in the Portland, Maine store: the gentleman who assisted me was great, turns out the size hinges I needed was being pulled from their retail outlets and going to catalog sales only. He had to dig through a couple of large tote bins filled with a couple of hundred assorted hinges and managed to find enough to fill my requirements. It would have been a lot quicker and less effort on his part to just refer me to the catalog. Another plus was that once we had the pile of the correct size hinges I needed, they were on sale for 60% off and saved me about $30.

Vs retail price in the catalog. Very satisfied store customer.

I used these hinges on an entertainment center with three inset glass doors. This is my first experience building and installing doors. Two of the doors would not close completely until I removed the set screw in the edge of the door. One of the hinges was bent when it arrived and had to be worked on my anvil to get it flat. One door still does not close perfectly. May be my construction but I feel the bad hinge may be the problem.

I guess I should have returned the bad hinge. The wrap around section of the hinge for the door appeared to be less than 90 degrees which could have caused the problem with the door not closing. Quality control seemed to be lacking. BEST ANSWER: This type of hinge is designed for use with Typical 3/4' Face frames -- also can be used for 1/2' doors in smaller application. BEST ANSWER: This type of hinge is designed for use with Typical 3/4' Face frames -- also can be used for 1/2' doors in smaller application.